# Yet Another 3D Printed Framework 16 Stand / Feet **URL:** \ **Category:** Framework Laptop 16\ **Tags:** framework-laptop-16-amd-ai-300, expansion-bay-shell\ **Created:** [January 23, 2026, 12:33am UTC](https://community.frame.work/t/yet-another-3d-printed-framework-16-stand-feet/80020 "2026-01-23T00:33:46Z")\ **Posts on this page:** 6\ **Page:** 1
**Author:** ![Graham\_King](https://sea1.discourse-cdn.com/flex001/user_avatar/community.frame.work/graham_king/32/42737_2.png) [@Graham\_King](https://community.frame.work/u/Graham_King)\ **Post date:** [January 23, 2026, 12:33am UTC](https://community.frame.work/t/yet-another-3d-printed-framework-16-stand-feet/80020/1 "2026-01-23T00:33:46Z")
I wanted soft rubber feet that wouldn’t fall off and fitted the Framework 16 without the GPU expansion. [Shared online](https://www.printables.com/model/1566649-framework-16-amd-ryzen-ai-300-series-laptop-stand) on printables in case anyone else is looking for something similar. Plenty of other similar 3D printables too, this is just another option. ![01](https://us1.discourse-cdn.com/flex001/uploads/framework3/original/3X/f/6/f6c514272c1241a7f62aa34b3c0899051c89af60.webp) ![04](https://us1.discourse-cdn.com/flex001/uploads/framework3/original/3X/6/d/6d720da00aebc507ae4382ee6fce9454527958bf.webp) ---
**Author:** ![jared\_kidd](https://avatars.discourse-cdn.com/v4/letter/j/91b2a8/32.png) [@jared\_kidd](https://community.frame.work/u/jared_kidd)\ **Post date:** [January 23, 2026, 3:18am UTC](https://community.frame.work/t/yet-another-3d-printed-framework-16-stand-feet/80020/2 "2026-01-23T03:18:06Z")
It doesn’t look like that clears the lid closing. If it doesn’t, it would be a very bad idea to use that on the laptop and you would be buying a new screen very shortly. Also doesn’t work if you have the dGPU installed. ---
**Author:** ![Graham\_King](https://sea1.discourse-cdn.com/flex001/user_avatar/community.frame.work/graham_king/32/42737_2.png) [@Graham\_King](https://community.frame.work/u/Graham_King)\ **Post date:** [January 23, 2026, 3:58am UTC](https://community.frame.work/t/yet-another-3d-printed-framework-16-stand-feet/80020/3 "2026-01-23T03:58:21Z")
Correct on both counts. These are removable feet for when the laptop is in use to aid ventilation, definitely not intended to be used with the screen closed. There are a bunch of similar 3d printable feet for dGPU expansion fitted systems available already. I don’t have the dGPU so needed some smaller feet. The only significant differences between these and the other similar feet I tried are these are designed to be printed in soft rubber (TPU), and they can’t slide off until you choose to remove them. Other similar feet I tried kept sliding off, and they were designed to be printed in hard plastic which I was concerned would damage the Framework case. And thanks, I hadn’t considered someone might want to close the screen with the feet attached, just because that’s not how I use the machine myself. I’ve added a note to the instructions on printables about that. ---
**Author:** ![Spooner](https://sea1.discourse-cdn.com/flex001/user_avatar/community.frame.work/spooner/32/29815_2.png) [@Spooner](https://community.frame.work/u/Spooner)\ **Post date:** [January 23, 2026, 12:44pm UTC](https://community.frame.work/t/yet-another-3d-printed-framework-16-stand-feet/80020/4 "2026-01-23T12:44:13Z")
The issue is that a laptop sitting out may be closed by someone without thinking. It may be fine for your use case, but it’s like balancing a glass of water on the edge of the table; it just takes one small mistake to cause a huge mess. ---
**Author:** ![JakeSully](https://sea1.discourse-cdn.com/flex001/user_avatar/community.frame.work/jakesully/32/45327_2.png) [@JakeSully](https://community.frame.work/u/JakeSully)\ **Post date:** [January 23, 2026, 1:10pm UTC](https://community.frame.work/t/yet-another-3d-printed-framework-16-stand-feet/80020/5 "2026-01-23T13:10:56Z")
kinda agree with other 2. Only needs some 1 at home or else where taking that laptop is about to flip over and they will close the lid and hear a big crack sound. So maybe include a sticker to be added on the bezel frame saying like “WARNING!: Do not close the lid while following laptop stan is in place on each side \< —— —— \>. Hopefully people reads it and then lets it be, but still a chance they don’t read it and still close the lid 😕 ---
**Author:** ![system](https://us1.discourse-cdn.com/flex001/uploads/framework3/original/1X/64c81a89f963ddb07633887baceb642a4b056046.png) [@system](https://community.frame.work/u/system)\ **Post date:** [July 22, 2026, 1:11pm UTC](https://community.frame.work/t/yet-another-3d-printed-framework-16-stand-feet/80020/6 "2026-07-22T13:11:39Z")
This topic was automatically closed 180 days after the last reply. New replies are no longer allowed.