We use a range of brands based on availability. Two sided SO-DIMMs will fit.
6 Likes
Will the Framework’s Motherboard BIOS support XMP?
(example crucial Ballisitx DDR4 3200 requires XMP to read at 3200 otherwise runs at 2666)
3 Likes
I’m also wondering about the XMP support in the bios.
1 Like
The Framework Laptop certainly supports DRAM that runs natively at 3200. We haven’t tested any memory that requires XMP to run at that rate.
1 Like
I can now confirm that the Ballistix 2x16GB 3200 kit (BL2K16G32C16S4B) runs at 2667 Mhz on my Framework i5-1135G7 and there is no option for XMP in the BIOS.
5 Likes
Never heard of XMP. Time to look it up!
1 Like
Thanks for confirming this so any user who see’s this post must find ram with a JEDEC profile that already runs JEDEC at 3200 nativity (sucks no XMP option but could happen in future boards or BIOS)
2 Likes
(post withdrawn by author, will be automatically deleted in 24 hours unless flagged)
Thanks for testing and confirming @jeshikat! We definitely recommend natively DDR4-3200 memory then.
4 Likes
Thanks for posting your results. I did suspect that this would be the case.
DDR4 RAM has tables to tell the motherboard how to automatically clock/time the memory. XMP is an extension of that table that specifies configurations outside of what JEDEC (the developer of DDR4) recognizes. You can think of XMP profiles as the memory manufactures’ tested-and-suggested overclocking profiles.
Anything not found in this table and running at 1.2 volts can’t be specified by the normal table as it’s not technically part of the standard. If your DDR4 so-dimm’s advertised timings is not in the table, or it’s not at 1.2 volts, it’s almost certainly using XMP profiles to get there. So be careful to avoid 1.35v modules for this laptop.
5 Likes
We’ve had a report of Kingston HyperX HX429S17IBK2/32 memory not booting on the Framework Laptop. We’re digging into what is causing this, since it should fall back to a standard JEDEC timing rather than not booting. In the meantime though, we recommend using non-XMP memory that runs natively at 3200.
3 Likes
The Crucial 2x16GB 3200MHz kit (CT2K16G4SFRA32A) works at full speed.
5 Likes
@jeshikat, any idea if that a dual rank kit? I’m guessing dual rank modules should work fine, but it would be nice to have some confirmation.
@speckledsea single-rank if I’m interpreting dmidecode right:
Array Handle: 0x0014
Error Information Handle: No Error
Total Width: 64 bits
Data Width: 64 bits
Size: 16 GB
Form Factor: SODIMM
Set: None
Locator: Controller0-ChannelA-DIMM0
Bank Locator: BANK 0
Type: DDR4
Type Detail: Synchronous
Speed: 3200 MT/s
Manufacturer: Crucial Technology
Part Number: CT16G4SFRA32A.C8FE
Rank: 1
Configured Memory Speed: 3200 MT/s
Configured Voltage: 1.2 V
Memory Technology: DRAM
Module Manufacturer ID: Bank 6, Hex 0x9B
There’s eight of these Micron chips on each stick: Part #CT2G8Z32DD8JC-062E | FBGA code: C9BKY
2 Likes
Hopefully the memory I have and was planning on putting in mine will run at full spec. I will post when I get my new Framework laptop if it works or not. 
What I already have: (2 x 8GB) G.SKILL Ripjaws 260-Pin DDR4 SO-DIMM (CL16) 3200MHz (Model F4-3200C16D-16GRS)
@DannyT, I was curious about that kit as well, but from what I’ve gleamed from this forum, I doubt the Framework run it at CAS 16, unfortunately, at least under the current BIOS. The tightest timing you can get for 3200 under JEDEC is CAS 20, so that should be your current best case.
According to what I can see posted about that kit (shout out to the hero on Newegg who uploaded a CPU-Z screenshot), the fastest JEDEC profile specified by the CAS 18 version of that kit is 22 @ 3200; the faster profiles are XMP 2.0. I’m guessing your CAS 16 kit follows that. So likely it will auto-configure to CAS 22 at 3200.
Please post your results when it comes in though! I’m interested to see what happens.
3 Likes
I am also curious if the dual rank version of Crucial 2x16GB 3200 kit works (CT2K16G4SFD832A).
I installed the G.SKILL Ripjaws Series 32GB (2 x 16GB) DIMM DDR4 3200 (PC4 25600) Laptop Memory Model F4-3200C22D-32GRS (CAS Latency 22, 1.20V) and it works fine. My batch from Newegg was single rank.
4 Likes