no, I run 11.
You missed the above 
Thanks for this nice guide and good idea!
I tried this out on Linux with the EasyEffects Tool and it seems to work. Sound seems clearer with the EQ applied but I did not test with the laptop on a table yet.
Be aware that you need to add an automatic preset to load the EQ profile while using the laptop speakers and another one without the EQ for the headphone jack which is only possible with actual headphones connected.
1 Like
I can certainly recommend putting it on a table!
Recently, I also tested extending the bass into lower octaves (e.g. 200 Hz), but that was not successful. The amplifier is too weak and volume drops on bass notes. So, we are stuck with how it is.
Just applied this on my Manjaro Linux system. It makes a subtle but noticeable difference. Thanks!
Thanks for doing this and sharing.
I am using the EQ shared previously here Speakers sound quality - #66 by Philonmetal I think this profile can be imported into APO giving another EQ style to choose from.
2 Likes
Ah yes, a very similar approach. While the filter coefficients are different, the outcome is probably quite similar.
I still want to do a measurement in a setup like that, where the laptop is on a table and the microphone over top. Unfortunately, in quick testing, the frequency response depends a lot on the position of the microphone, so I have to perform some averaging over different listening positions.
Well if you do end up taking more measurements and making another EQ please do share your results.
Hopefully in the future the speakers can be tuned by Framework as the right EQ seems able to transform the perceived quality of the speakers.
Yes, I would expect that.
Usually, integrated Class-D amplifiers, as used in this laptop or other mobile devices, include a digital signal processor (DSP) component. That has become very common, even in the cheapest circuits.
Filter coefficients can be loaded at production time, and the speakers are driven with corrected inputs, without the need for any software.
Sure, I will provide new measurements when I make them!
1 Like
Different people have different ‘needs’ Younger people hear louder high frequencies and older louder low ones, so I’m not sure the speakers can be tuned to suit the majority of people if that’s what you mean.
Personally I have no problem with the sound. I usually have the laptop on stainless steel 2mm thick sheet to ensure the air cooling inlet is ‘protected’.
Equally when on a wooden surface it seems fine.
My use of the equaliser is only to pass the audio to my very intense bassed up Marley speaker if I want watch a film etc.
1 Like
The speakers can certainly be tuned to sound much better to most of the listeners.
Please note that the settings I posted are not subjective, they only remove the defects in frequency response from the speaker outputs. Filter parameters were optimized such that the resulting frequency response is flat. Thus, the speakers represent the sound as it was intended to be listened to (apart from the missing lower and higher octaves, which the physical speaker is not capable of reproducing).
If the frequency response is not flat, the speaker introduces some characteristic “sound” which a listener might like, but that is not fully representative of the source material anymore.
However, the deviations that the Laptop speakers show (10 dB at crucial frequencies) are not acceptable “sounding” anymore, in my opinion. The speakers are just not engineered very well.
11 Likes
@elagil : Thanks for your work. I’ve had my Framework 12th gen for 2 weeks and that bump in the mids was quite annoying on speech content, especially as i am a sound tech/musician
1 Like
Just to be clear, this is for the base speakers, and not the optional/updated 80dB ones?
Is the equalizer site blocked for anyone else? I also see it on sourceforge but I’d prefer the original source.
Yes, I have only the base model and don’t have measurements of the updated ones. Presumably, they just have a lower impedance coil for higher efficiency. Maybe they measure in a similar way.
It is not blocked for me. Here is the direct download link, if that helps: https://equalizerapo.com/EqualizerAPO64-1.2.1.zip
1 Like
sourceforge has the much newer v1.3. how come you guys aren’t using that one? Equalizer APO - Browse /1.3 at SourceForge.net
When looking at https://equalizerapo.com/contact.html
…and please note that we’re not the official developer of this software, therefore issues related to source codes are beyond our expertise. In such cases we advise you to contact the developer directly. We are here to help if you need any assistance with setting up the Equalizer APO.
and
This website should be used only as an informative source and not as an official reference.
So not the official source, maybe the sourceforge page is the project home?
I found adding thin rubber pads to the top and bottom of the speakers helped. They also helped firm up the keyboard when placed on other flat areas under the keyboard. They are the smallest ones in this set. About 1mm thick and 6mm in diameter.
https://www.amazon.co.uk/gp/product/B0140WM84O/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
2 Likes
Yes, it seems like that is where the code lives - as well as the releases.
1 Like
Thanks! That really does help. Now if I can only get the whole thing to stop rattling at any volume over 50%.
1 Like