[RESPONDED] USB-A Expansion Card stops working until unplugged

[rcm]

12gen Framework (3rd batch i7-1280p).

Today I noticed that USB 3-3 (bottom right when viewed from above) wasn’t working. Only until I unplugged and reinserted the card did it start to work. After some time, I tried again and it wasn’t working again. Again, after unplugging and reinserting the card did it start to work.

The same behavior is observed while sitting in the BIOS.

I tried a different USB-A expansion card in the same slot, and the problem seems to be unique to the slot, not the card itself.

[anarcat]

Hey, I have the same problem! I thought I was going nuts or that the USB key (my yubikey!) was going bad, but I have the exact same situation.

Are you running TLP or power savings tuning by any chance?

It could also be a regression from the 3.06 upgrade… see 12th Gen Intel Core BIOS 3.06 Beta where i’ll post a followup comment linking here…

Update: actually, that post explicitely mentions this problem, and a workaround

@Kieran_Levin

Note: One user has experienced that after updating some type-c ports will not function in DP alt mode, If you experience this please report to the forum and power off your laptop, remove AC, wait 2 minutes and power on again.

So I guess I’ll try that next!

[anarcat]

@Kieran_Levin

Note: One user has experienced that after updating some type-c ports will not function in DP alt mode, If you experience this please report to the forum and power off your laptop, remove AC, wait 2 minutes and power on again.

So I have just tried two things:

1. a reboot
2. turning off the laptop for two minutes

I naively thought a reboot would be enough but no, the above is correct and you need an actual full two minutes off to have the USB-A device return to life. It is not really a workaround: it’s much simpler to just remove and re-insert the expansion cards (and that works reliably)…

[anarcat]

@rcm

bottom right when viewed from above

also, I suspect that does not matter at all: i’ve witness the problem on the top and bottom left of the laptop, and I suspect it would similarly happen on the right side as well.

I reported the issue as well in 12th Gen Intel Core BIOS 3.06 Beta - #68 by anarcat.

[rcm]

Ah yeah it doesn’t matter, both sides behave the same actually.

[anarcat]

@Matt_Hartley is this BIOS 3.06 regression on your radar? I mentioned it in the 3.06 beta thread but i suspect it was lost in the noise… It’s quite a regression, and the workaround (unplugging the USB-A card and plugging it back in) works, but it’s quite annoying…

[Matt_Hartley]

We sure TLP is not installed? It will produce this behavior unless the right setting is blacklist or changed. Went through it with my USB devices. Fixed it pretty quickly. Let me know.

Setting aside the behavior in BIOS for a minute as that would be another team.

[rcm]

TLP is not installed.

[brn_castro]

Same here, I don’t have TLP installed.

[anarcat]

@Matt_Hartley

We sure TLP is not installed? It will produce this behavior unless the right setting is blacklist or changed. Went through it with my USB devices. Fixed it pretty quickly. Let me know.

TLP is definitely installed here, I wasn’t aware that an extra hack was required after the upgraed, what is it?

[Matt_Hartley]

For those who do not have TLP installed, please try different expansion slots and some A/B testing with the installed distro vs a Live distro. It’s annoying, but it provides to environments from which to test from.

@anarcat For TLP, I’ve used this setting successfully with some devices. Not using with USB-C expansion myself, but am using for DP and HDMI.

Took the screenshot using TLPUI since it is more visual than TLP’s config. I’d locate the USB ID and exclude it from TLP’s USB suspending. Worth a shot to see if this helps. Then reboot.

[anarcat]

thanks @Matt_Hartley ! as it turns out, using another USB-C port seems to have fixed the issue… And anyways, I have switched to a dock now, so the issue is less pressing (or, rather, changed radically), see:

USB C Dock question

I just got a Cable Matters hub: That promises “Linux” support and checked all the boxes for me (4x USB-A, audio, network, 2xHDMI). It … kind of works? I tested the USB-A ports, charging, networking, and the HDMI ports, all worked the first time. But! When I disconnect and reconnect the hub, the HDMI ports stop working. It’s quite infuriating especially since there’s very little diagnostics available. It’s unclear how the devices show up on my computer, I can’t even tell what device provides …

[Matt_Hartley]

@anarcat

thanks @Matt_Hartley ! as it turns out, using another USB-C port seems to have fixed the issue… And anyways, I have switched to a dock now, so the issue is less pressing (or, rather, changed radically), see:

Doing some catching up, thanks for the heads up.