@Christopher_Brown Ohhhh… Looking up part number yeah… Not sure how I missed that, but yeah, definitely not OLED. So gonna return this one and sulk back to the drawing board. Thank you for catching that (just in time)!
1 Like
Here’s the 3 panels which should be a drop in replacement. First one is what Framework come with, available in glossy or matte. 2nd one is brighter less contrast. Third one is similar to 1st but only matte. Panel Compare
There is this 13.4" 3840×2400 part # LQ134R1JX41 which is 3mm wider and 10mm shorter. Just not sure there’s enough room on the width to cut it out bigger and fit in the lid.
There is also a 13.0" 3000x2000 screen that would be a bit smaller, larger bezel but more resolution and a scaling of 200% would be ideal for me. LP130QP1-SPA1
Or a 13.3" that is also 3000x2000 and might fit better P130ZZA-BZ1
All of these should work with some lid/bezel mods.
1 Like
I don’t think that larger will fit at without significant modification. The width may be doable by removing the magnets on the side but the height won’t work at all without removing the switches etc up top and even then would probably be too tight.
The smaller may work without too much modification, just need to center them on the aluminum bracers and may have some margins showing? Not sure from measuring but could just use electrical tape to cover the gap… Can see the benefit of the higher res with scaling.
For me though, all the panels linked all look like TFT displays. I’m still trying to find a nice OLED panel and am trying to find what’s in the HP Envy x360 before getting a screen replacement to try out…
I’d have an interest in finding compatibility with some smaller screens, sub 12 inch, like maybe 10.1 inches for making a DIY smaller version of the Framework. You’d be restricted by the width of the motherboard and battery, but still cuts a good 5-6cm off the width. If just using the eDP connection this could be possible and no need for USB cables.
1 Like
Look at this:
1 Like
This Acer Digitizer works with two separate I2C Interfaces (which is the 8 pin header) for finger touch and stylus touch. Does somebody know how to connect such to the mainboard or via external connector?
If you want to post the part number for that display, I can look into the datasheet.
1 Like
Well, the display itself connects straight forward. Its the one from acer spin 7 - and it seems like it is the same as frameworks own.
The Touch Screen Controller, that is the part I am curious about.
There is some “part number” on that… H133820-S-1330-V0 I did some googling, bit did not find any result to these… Could be Acer’s own/internal. Acer Spin 7 Connection Sheet says it is connected via two separate I2C Connectors - one for stylus input and one for finger touch. So they just have to be connected to the board somehow…
funny enough - I also cracked my first panel 
I’ll buy a glass cutter to retrofit the next one in the original case…
im looking at using a dell xps 13 oled screen. the oled is from a 9310.
would this screen be compatible?
Seems like that would be 16:10, so it wouldnt be as tall as the framework panel even if you can get it to interface correctly
Framework 16 is 16:10
2 Likes
Seems they’re looking at a 13" class panel though, as its a 9310.
2 Likes
this guy managed to get it interfaced to an ipad 7:
I am about to get a Framework Laptop 13, and looking for some OLED display replacement.
This one seems great, OLED, 13.3 inch, 3:2 ratio, 3000x2000, eDP 40pin.
Is there anyone had tried this?
https://www.aliexpress.com/item/1005005705593587.html
The samsung oleds use a different pinout on the same connector (and uses 1.8v io instead of the normal 3.3v for some pins and very different supply voltage), I would be very careful.
Sauce: blew up my t480s mainboard plugging a different samsung oled into it before checking the pinout because I was so used by everyone using the de-facto standard (managed to mostly “repair” the mainboard but still not a good idea).
1 Like
since framework started selling the edp cable by itself, I jumped back into the idea of homebrewing my own smaller framework
what does everyone think about
-
this 4k 11.6 display from BOE, panelook link, in short its 40 pin non touch edp, edp 1.4 but its 4 lane, far as I know both the framework 13 motherboard and cable are 4 lane compatible
-
this 2k 10.1 display from Panasonic, panelook link, its a 40 pin edp, uses 2 lanes BUT its edp 1.3, which Im not sure if its compatible with edp 1.4 on the motherboard
I might buy the datasheets for both but I dont know if it would be worth the cash to put in the effort, would these have a similar pinout to the default 13.3" display? would it be worth even looking into?
So was just doing a little digging on this and can’t find the exact panel mentioned (The ANTA35VJ01) But I can find the ANTA33TP11, the pinout is for sure different - but the voltages are the same - 3.3v. So it’s not a lost cause if you wanted to make an adapter board that connected up the wiring properly.
(for anyone looking for panel info, if you register for Panelook then verify your ‘business email’ you get point to buy manuals. You can just use a temp email service and change your email each time you need points.)
edit: actually saying that, there are a few pins which don’t have obviously corresponding ones, but might be possible with some digging. (e.g. 'VBAT: Power for EL PMIC… it might be backlight power, as it’s otherwise missing… but all a bit of a risk without knowing)
1 Like
Google returns 0 results for that one.
Would not bet on it, all the samsung oled datasheets I have been able to dig up had 1.8v io pins, still 3.3v for logic supply power but the io is 1.8. Level shifters are a thing so that’s not a huge issue, especially if you compare it to the power supply but it is a thing.
Making an adapter board is well withing the realm of doable but it would have to be done. Compared to the dc-dc converters you’d need for the power a couple level shifters aren’t a big deal. And it’s not like you are particularly space limited as long as you keep your board thin enough, oled panels are so much thinner than lcds you can just put that stuff behind the panel on a retrofit.
But as long as there isn’t a good oled that actually fits the 13 I have put that project onto ice.